Description
What does this mean?
OBD2 Code P0201 Renault definition:
P0201 Renault means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of OBD code P0201 Renault
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Causes
Possible causes of OBD code P0201 Renault
The causes could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
The OBD2 Code Information Be Applicable For Renault:
2013 Renault ZOE,2013 Renault Twin-Z Concept,2013 Renault Twin-Run Concept,2013 Renault Talisman,2013 Renault Symbol,2013 Renault Scenic XMOD,2013 Renault Fluence,2013 Renault Espace,2013 Renault Clio,2012 Renault Twingo,2011 Renault Megane,2011 Renault Latitude,2011 Renault Laguna Estate,2011 Renault Laguna,2011 Renault Frendzy Concept,2011 Renault Captur Concept,2010 Renault Scenic,2010 Renault Megane RS,2010 Renault Megane Estate,2010 Renault Grand Scenic,2010 Renault Fluence,2010 Renault DeZir Concept,2010 Renault Clio RS,2009 Renault Twingo RS,2009 Renault Symbol,2009 Renault Scenic,2009 Renault Safrane,2009 Renault Megane,2009 Renault Laguna GT,2009 Renault Laguna Coupe,2009 Renault Koleos,2009 Renault Kangoo,2009 Renault Clio Campus,2009 Renault Clio,2008 Renault ZE Concept,2008 Renault Twingo,2008 Renault Sandero,2008 Renault Laguna Estate,2008 Renault Laguna,2008 Renault Kangoo,2007 Renault Megane,2006 Renault Twingo,2006 Renault Thalia,2006 Renault Nepta Concept,2006 Renault Kangoo,2006 Renault Espace,2006 Renault Clio Sport,2006 Renault Clio RS Concept,2006 Renault Altica Concept,2005 Renault Z17 Concept,2005 Renault Vel Satis,2005 Renault Modus Initiale,2005 Renault Laguna,2005 Renault Clio III,2004 Renault Modus,2004 Renault Megane,2004 Renault Clio,2003 Renault Scenic II,2003 Renault Be Bop
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Renault makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.
